Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

Gavin_yang
  • Locked
  • Question
RSS Tolerance Questions! 2
Replies
7
Views
3K
Gavin_yang
Gavin_yang
AMontembeault
  • Locked
  • Question
Multiple Single Segment Positional Tol and Datums
Replies
7
Views
1K
3DDave
3DDave
ericscottf
  • Locked
  • Question
Proper GD&T for interrupted threads?
Replies
14
Views
964
ericscottf
ericscottf
dogbural
  • Locked
  • Question
profile tolerance for chamfer and radii
Replies
2
Views
865
Wuzhee
Wuzhee
FrancoisY
  • Locked
  • Question
What is this symbol? 2
Replies
9
Views
936
Wuzhee
Wuzhee
DimaM
  • Locked
  • Question
GD&T: How to inspect tertiary datum feature position tolerances?
Replies
7
Views
975
Burunduk
Burunduk
Jack.Smith
  • Locked
  • Question
Tolerancing of features to a center line of a thread
Replies
4
Views
681
Burunduk
Burunduk
Glass_Half_Full
  • Locked
  • Question
How Many Datums are Too Many Datums?
2
Replies
29
Views
2K
greenimi
greenimi
ndpaintballer
  • Locked
  • Question
Question about controlling bow on extruded profile
Replies
12
Views
898
3DDave
3DDave
PtoMonty
  • Locked
  • Question
Position tolerance datums 3
2 3
Replies
42
Views
2K
PtoMonty
PtoMonty
Topcat75
  • Locked
  • Question
TED's and Profile Line/Surface Help
Replies
4
Views
571
Topcat75
Topcat75
MPSU
  • Locked
  • Question
Primary Datum on two planes
Replies
7
Views
1K
MPSU
MPSU
Mech1595
  • Locked
  • Question
Datum Targets in MBD 1
2 3 4
Replies
65
Views
2K
3DDave
3DDave
Auxcron1
  • Locked
  • Question
Reference Point System 1
2
Replies
38
Views
1K
pmarc
pmarc
Rayleigh
  • Locked
  • Question
Fraction in Decimals within drawing. 7
2 3
Replies
50
Views
2K
Mech1595
Mech1595
dGhost
  • Locked
  • Question
ASME Y14.5 vs ISO 1101 in Australia / internationally 4
Replies
8
Views
994
dGhost
dGhost
supergee
  • Locked
  • Question
Measuring runout on a shaft relative to two datum surfaces... part 2
Replies
3
Views
566
supergee
supergee
MPSU
  • Locked
  • Question
Slot as Primary datum for a Blow Molded Part
Replies
15
Views
693
Eric Gushiken
Eric Gushiken
MPSU
  • Locked
  • Question
Positional Tolerance of a Corner profile
Replies
7
Views
539
Doug Hunter
Doug Hunter
Blue33
  • Locked
  • Question
how to properly use the centerpoint of a specific circular section of a hole as a Datum
Replies
2
Views
502
Burunduk
Burunduk
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top Bottom