Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Bearing design, manufacture and maintenance

Cesto
  • Locked
  • Question
Large plain bearing suppliers
Replies
3
Views
206
geesaman.d
geesaman.d
Basit Shafi
  • Locked
  • Question
Ball and Roller Bearing Stiffness approximate Models for rough estimation
Replies
3
Views
418
lucky-guesser
lucky-guesser
Daren Samy
  • Locked
  • Question
Axial thrust in vertical pumps
Replies
0
Views
277
Daren Samy
Daren Samy
SMKRe
  • Locked
  • Question
Double-offset journal bearing & offset-elliptical journal bearing applications and advantages
Replies
0
Views
246
SMKRe
SMKRe
CharlieHT
  • Locked
  • Question
Looking for: A pivot assembly which is smooth but also has enough friction to hold 1kg.
Replies
2
Views
389
TugboatEng
TugboatEng
Walther1522
  • Locked
  • Question
Bearing Design Calculations and Help
Replies
4
Views
346
geesaman.d
geesaman.d
ktgottfr
  • Locked
  • Question
Bearing lubrication flowrate effect on lubrication regime
Replies
11
Views
735
electricpete
electricpete
electricpete
  • Locked
  • Question
buying rolling bearing at the small end of the bore tolerance? 4
Replies
6
Views
356
geesaman.d
geesaman.d
MacMcMacmac
  • Locked
  • Question
Proper Bearing Lubrication 1
Replies
3
Views
423
electricpete
electricpete
Melvin84
  • Locked
  • Question
Food proof bearing units 1
Replies
3
Views
223
Melvin84
Melvin84
bamia
  • Locked
  • Question
Pulley bearings 1
Replies
6
Views
301
JS_
JS_
rollingcloud
  • Locked
  • Question
Are formed race inner surface w/ liner typically controlled geometrically?
Replies
0
Views
169
rollingcloud
rollingcloud
rollingcloud
  • Locked
  • Question
Any tips on removing PTFE liner? 1
Replies
2
Views
235
rollingcloud
rollingcloud
umatrix
  • Locked
  • Question
Bearing Tolerance - Radial, Axial and Tilt angle ?
Replies
2
Views
482
TugboatEng
TugboatEng
Ricko Bambino
  • Locked
  • Question
Schigley's example 8-7
Replies
0
Views
144
Ricko Bambino
Ricko Bambino
rollingcloud
  • Locked
  • Question
Does this bearing fall under any standards/specs? 1
Replies
5
Views
307
rollingcloud
rollingcloud
rollingcloud
  • Locked
  • Question
Do roller swaging & proof load test remove passivation layer of outer surfaces of the bearing ra 1
Replies
11
Views
434
rollingcloud
rollingcloud
Amine A
  • Locked
  • Question
Design Ansys
Replies
0
Views
111
Amine A
Amine A
bamia
  • Locked
  • Question
Hello everyone, I have a conveyo
Replies
8
Views
310
Tmoose
Tmoose
madsmadsmads
  • Locked
  • Question
Linear motion bearings in motor spindles
Replies
1
Views
197
TugboatEng
TugboatEng
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top Bottom