Hi Captain,
I am not sure of the part and extent you want the fuel to take in the analysis. However a simple level you could represent the fuel load by a distributed pressure load that changes with fuel depth. This could represent the static load of the fuel. For bulk acceleration of the fuel an...
AS CWIC says you cannot get the material back to its initial state:
1) The parent material is in the T8x condition, which is solution heat treated, cold worked and then artifically aged. Near the welds this temper will be lost. After welding you could solution heat treat and artifically age...
The choice of software should be driven by what you need to do with it. Look at typical jobs that you will need to analyse and draw up a list of things that you may need to include (e.g. contact, thermal, stress, vibration (type), 2D or 3D?) and how you want to use it (how often, in CAD, expert...
As you were out of maintenance I think an admin fee is reasonable, but $2000 is way too high. I suspect this is a punitive measure to "encourage" you to go back on maintenance. Go back and talk to ANSYS, If it means loosing your 'potential' future custom I suspect they would wave or...
SeatrendSam
Unless there is a specific requirement like that described by Mloew above I cannot see the logic in this technique.
The accuracy depends on a number of factors, but I will limit discussion to mesh density issues. As the mesh is refined the solution variables should converge to the...
chairats,
I am assuming you want to know how to do contact analyses rather than learn about the programing.
The following book is really about contact mechanics and is a good place to start:
K L Johnson, 'Contact Mechanics', Cambridge University Press.
Also NAFEMS (www.nafems.org) have...
Cristina
I assume you are using ABAQUS/CAE for the input modelling. Unfortunatly CAE has quite poor facilities for directly creating complex surfaces. The only practical way of getting your data into CAE is to use a proper CAD package to define the surface as a NURB or as facets and then to...
I am not sure about IDEAS, but it is probably an implicit code which is not good for capturing short duration events (it can do it but it will be very inefficient). LSDyna is a explicit code which should handle the impact event very well - that what explicit codes were designed for. This may...
sgdon
A lot will depend on the type of composite and what you are trying to find out. For instance:
"A random nano-composite used to make a macro component and a you want to find the macro stresses could be analysed as a homogeneous isotropic solid."
At the other end of the scale...
Are there any NAFEMS registered Analysts out there? Apart from receiving the excellent Benchmark magazine, have you encountered any other benefits of this title? eg, in no particular order:
1) Promotion because you are an 'expert'.
2) Given as evidence of professional competence in
biding...
CADfix, I beleive has the most advanced mid-surface extraction reoutins, see:
http://www.transcendata.com/products_cadfix.htm
The software will also allow repair, defeaturing etc of the model.
TERRY [pc2]
Dear elogesh,
It is difficult to determin why there might me a difference between the Test and FEA without seeing the detail of what you have done. However consider the following:
1) Your model probably has isotropic homogenious material data. Castings are neither of these. Firstly it is not...
* If you do a non-linear analysis you should get true strains.
* A linear analysis will usually give engineering strains.
Another important bit to remember is not the outputs but the inputs of the analysis. If you are doing a non-linear analysis the material properties input will ususlly need...
Are you sure you are taking the correct approach? Elastic foundations are often assumed to be semi-infinite half spaces. I am not sure if ANSYS assumes this?
From your description your 'foundation' does not seem to be semi-infinite. In which case you will have to take into account the material...
trainguy
Test, Test, Test - even if it is a scale physical model or a another simplification of the real structure. Of course you can do simple bounding calculations on many components that act non-linerly, although the bounds may be quite wide. There is no simple single answer, execpt that the...
