Hi Friends,
I'm trying to determine the origins of the terms "FPM" and "FFPM." It's not uncommon to see "FKM/FPM" or "FFKM/FFPM" (or variations) when generically specifying fluoroelastomers and perfluoroelastomers respectively—or fluorocarbon and perfluorocarbon rubber if you will. From both...
Consider ASME BPE (Bioprocessing Equipment Standard). Section SD-4.7 in the 2009 edition would be a starting point. Since the contents will be used in "pharmaceutical" products, it follows that ancillary systems that convey raw materials to be used in those products must meet the same...
I have it on good authority that the siding is galvanized steel and the base metal has the spangle patterning typical of galvanization. We definitely don't want to replace the siding itself.
I've read that alkyd paints are not suitable for direct application to galvanized steel (i.e., must use...
The area to be painted is quite large. It is an 8-story building and the siding is under and between windows on each floor on three sides of the building. I estimate about 4000 sq.ft. Click here for a pic of the building. Everything that's gray needs to be painted. You can see that it's not...
Hello fellow engineers!
I live in a 100-year-old building with painted galvanized steel siding. The paint is severely damaged and is flaking off (please see pics). There are areas of surface rust, but nothing I would consider serious. I do not know if this is the original paint or if/when...
Thanks Charles,
I'm involved in that very industry and discussed this further with Guy R and John D at the recent BPE meeting in Dublin (John and I work for the same company). I appreciate your comments and they will certainly add value to the thread. I was just looking for third-party...
CodeJackal,
Thank you very much for your valuable input! I don't have access to PVHO at the moment, and the information you provided definitely put things into perspective.
Scott
Scott
======================================
"You can marry more money in five minutes than you can make in a...
Hi friends,
According to this web page, pressure vessels conforming to Section VIII may incorporate acrylic cylinders and be U-stamped. The page goes on to say "The American Society of Mechanical Engineers (ASME) has now approved the use of acrylic in the construction of pressure vessels under...
BoomerSooner7:
You said...
Unless I'm missing something, I disagree with that statement. The motor also "sees" the torque required to rotate the impellers that pump the fluid. As you increase the flow rate and/or TDH, the required BHP also increases.
I'm guessing that the purpose of your...
Metengr,
Thanks for your reply. Of course, if the customer is willing to pay for it, we're willing to build it. Your statement that
is what really caught my attention. If, indeed, the code does not consider operational scenarios, then from a technical fabrication perspective—which is my...
Hi friends,
I work for a company that manufactures liquid chromatography columns for biopharmaceutical purification. On most customer specifications that I receive for these columns, a U-stamp is requested or, at least, "conformance to Section VIII." I am also involved with the authoring of a...
Thank you everyone for the responses thus far. To be clear, I am trying to understand the design origins of the typical control valve actuator (or "top works"). For a diaphragm actuated assembly, the diaphrgam is usually 8 to 12 inches in diameter and sits on the very "top." It is either...
I am confused by all of the features normally found on a "typical" control valve actuator. To keep this post simple, I am referring to the traditional diaphragm actuator type represented in the link. The purposes of the diphragm, spring, and actuator shaft are obvious. However, if all I'm...
Thank you to everyone for your input. As an update, it turns out there never was any slag or other imperfections. We inspected the welds optically with sight tubes and they were clean. Lens and lighting effects from the borescope created the illusion of imperfections. A good experience for...
