These were created about 12 years ago when we were first learning NX. At the time it worked and I am sure there are many better ways to get the same result. Once we created the parts that needed these types of if statements we have not created anything since then, until now when we ran into the...
I found what I was looking for. At the end of the if statement you can have the else point to another expression.
The expression is named METRIC_BODY_Dia and it points to METRIC_BODY_Dia2 at the end. This then ideally continues the if statement.
Thanks to all for your input...
I believe that there is a length limit of 1024 characters when creating an expression with an if,then,else statement.
I also thought that there was a way to go beyond that by putting something at the end to have it look at another expression to continue the if,then,else statement.
Does anyone...
Good morning Taylor,
Thank you for all the information.
The issue is that there are many ways to work in NX.
Most of our designs are a one off and do not require any formulas or association with measurements.
In PR 9154870 we had a body in the top level assembly that was being used in the...
I have 2 PR's
IR 9154870 has been converted to PR 9154870; Desc: 12.0.1 MP1 Measure Distance fails when a body resides in top assembly file.
IR 9155038 has been converted to PR 9155038; Desc: New Measurement is not working within a Sketch.
Both have been flagged as critical.
I know that you...
Thank you for the program.
Actually we created a program within excel to give a report.
Select all faces and do an info report. Copy the entire report into excel and run the program.
Just comes back with a list of colors used within the entire part, it actually shows the little color box that...
Just installed the latest mp for NX 12.01.
The measure command has been drastically changed.
Has anyone else seen the changes?
Any comments?
There were several bugs that we discovered and as a result have rolled back before the mp.
I have 10 designers and non of them like the changes.
The PDF...
Good morning.
Does anyone know of a way to get a list of what colors a part is using.
We have a color map that the designers use. They are only supposed to use the 60 favorite colors but sometimes the rules are not followed.
Is there a way to interrogate a part and get a list of what colors...
Hello to the group.
We are running in managed mode with TC10.
In NX9 whenever you RMB on a component within an assembly the attributes tab context "Apply to" defaults to Component.
Even after you select "Part" on the "Apply to" pull down it will revert back to "Component" if you select apply...
Hello to the group.
I am sure this is very simple for someone familiar with macros or journals.
In NX9 it seems that when you select a component in the assembly navigator and select properties the attributes tab defaults to setting the attributes at the component level. What I want is for it to...
Problem resolved. We had a modified "ug_view_popup.men" file in which we made changes so that when you held down RMB you had other options than the default. This file seems to have messed up the options when you tapped MB3.
Thank you for your suggestions.
Regards Jurgen
NX9.0.2.5
I can no longer set my rotation point as was able to do in NX8.
In the graphics window you can tap RMB and get a list of things you can do.
One of them is set rotation point (3 up from the bottom). When I select this then the error "None of the actions specified for this button were registered...
All our designers have a space pilot pro. Works great in NX8 but we have found an issue in NX9.
In NX9 you cannot set the rotation point. In the 3Dconnexion ribbon the buttons are greyed out. Using RMB in the graphics window and selecting "Set Rotation Point" gives the following error.
"None of...
Mike,
I am sure that J. Baker will correct me if I am wrong but I was told by my instructor that the MODEL reference set was a special reference set that would be automatically created even if you deleted it. Under customer defaults you can set what gets put into this reference set...
