Right, I see. Well basically, we know the piping would be susceptible to land slippage in this area so we conduct surveys to quantify the displacement. The displacement is then compared to set allowable displacement values so the precision I'm looking for would be to the mm.
I honestly can't...
Hi guys, thanks for your thoughts on the matter. My apologies, it is above ground piping and currently, the vendor is using a total station survey. Specifically, use of the total station for horizontal displacement, and digital levels for vertical. A system of control points were set up along...
Hi All,
Firstly let me start off by saying I'm not well versed with all the lingo associated with Surveying, so please forgive me if I use some of the terminology incorrectly. I just wanted to get some input / advice with respect to performing a pipeline survey to monitor movement of the piping...
But even though there is a long seam weld, isn't the weld itself typically stronger than the parent material? So provided the weld is 100% acceptable as per RT, why can't the higher stress value be used?
Oh dear, Yes, Monday's are really the worst.. the gasket thickness is 2mm, sorry about that error, as glaring as it is.. anyway, yes, the process is nitrogen dioxide..so I can't afford for a gasket to go up there and fail at all.. 10 bars @ 490 deg. C.
Hey Everyone,
I have an urgent problem here, basically, I've got a vessel with an operating pressure of 10 bars. The incorrect gasket was used to seal to top cover flange of the vessel (approx 3950mm in diameter). The correct gasket was now specified in terms of material, however, two different...
Hey all,
I'm fairly new to fabrication and welding, so I wanted to find out if there is a difference between a weldolet and a flat weldolet. I have to specify one for replacement, and according to my Isometric, its specifying a flat weldolet. I did a little digging and saw somewhere that flat...
Hi guys,
I have a little problem. I'm trying to determine the inlet flow velocity of fluid to my pump. It's a 4 stage vertical turbine pump and its situated to one end of a well. Water flows into the well via a 24" diameter pipeline at an entrance velocity of approximately 8 ft/sec. Now the...
I'm assuming cost is a major factor to you? I'm familiar with butterfly valves which carry the nylon 11 coating. It works well in our seawater applications and protects the disc from corrosion. Is this for temporary use? Or long term? As mentioned above, the coatings do chip overtime as no...
Good day,
Happy New Year to all of you.
Young Engineer here, and I have a question about the material of a particular valve. We've got 30" butterfly valves that are underwater (seawater) and are currently in need of replacement. Unfortunately, the valves are obsolete and are not manufactured...
Ok let me explain the full story..sorry, I should have done this from the start..the decision was made based on Engineering review that we should fit larger impellers on our Pumps. (6 single stage vertical turbine pumps rated at 8287 usgpm @ 191 feet of head)The larger impellers were supposed to...
Good day,
We're considering trimming the impellers on our 6 vertical turbine Pumps. Pumps are consuming too much power and we'd like to reduce it by trimming them. I would like to know, is there any particular method / procedure to trimming impellers? The impellers are semi open impellers. Do...
Good day,
I just need confirmation on something. I have a 12 stage horizontal centrifugal pump. I have recorded values of flow, suction pressure, discharge pressure and speed. I'd like to work out the flow and differential head values to the rated speed. I've applied the affinity laws:
N1/N2 =...
Ok ok..let me explain exactly what I want to do..(Sorry, should have done this before) , I'm trying to determine the pump's BHP from operation. I dont have any flowmeters so I cant tell using the flow. So I was trying to determine how to get the motor output horsepower, then use the motor's...
Ok, so is the power its producing equivalent to when you multiply the power its using by its efficiency?? Am I correct??
And the power it's using is found using the above equation?
