You aren't preventing piping - in fact, you are encouraging it to form through the slits. That's a very bad idea!
It sounds to me as though the drain is simply too small to act as a proper filter. And the gradation of your "super clean" sand may not be appropriate for a sand filter. Also be...
Agreed.
[pacman]
Please see FAQ731-376 for great suggestions on how to make the best use of Eng-Tips Fora. See faq158-922 for recommendations regarding the question, "How Do You Evaluate Fill Settlement Beneath Structures?"
Do you have Burklin's full name? Or a citation of a paper s/he has co-authored?
[pacman]
Please see FAQ731-376 for great suggestions on how to make the best use of Eng-Tips Fora. See faq158-922 for recommendations regarding the question, "How Do You Evaluate Fill Settlement Beneath Structures?"
Hmmm,
You never indicated what type of structure that you are concerned about. Office buildings have one set of concerns; transmission towers for high voltage power lines are quite different. (Industry expectations and acceptable consequences of failure cause the major differences.)
I use...
JamesDean7:
Why not start a new message thread? You'll get more respondents that way -
[pacman]
Please see FAQ731-376 for great suggestions on how to make the best use of Eng-Tips Fora. See faq158-922 for recommendations regarding the question, "How Do You Evaluate Fill Settlement Beneath...
I agree with most of what PEinc has posted. But over the years I have learned to be more tolerant of other construction methods when site conditions don't require "best performance", only "ordinary performance." I know almost nothing about geoeng05's alignment; but it is quite possible that...
If the problem is large, complex or critical, stick with p-y curves and the current version of LPILE to model your problem. Make good use of the technical support offered by the program's developers.
If the problem is small and simple, use Broms' hand methods. They're fast, pretty cheap - and...
Forget the square U shape unless you are prepared to live with cracks/distortion at the corners. Stick with a reasonably square shape - you will have far fewer problems that way.
The soils get better as you move north of Buffalo Bayou - so yours should be pretty good. SHOULD. But you also...
Very few reputable engineers/firms see any real benefit in using it, I suppose. There isn't much market for it.
[pacman]
Please see FAQ731-376 for great suggestions on how to make the best use of Eng-Tips Fora. See faq158-922 for recommendations regarding the question, "How Do You Evaluate...
Depending on the soil profile, a cutoff wall may be a very good solution. What does your geotechnical engineer say?
[pacman]
Please see FAQ731-376 for great suggestions on how to make the best use of Eng-Tips Fora. See faq158-922 for recommendations regarding the question, "How Do You...
Took the seismic twice; the first was developed by the Board, second by the test service. The first one was terribly obscure - not sure why a geotechnical engineer needs to know how to detail a roof to wall connection. A really poorly considered problem.
The second test covered seismic design...
Well, I'm a legitimate Texas Ex - so "Hook'em" sounds good to me!
HgTX gave you the citations. Now for the "hard to swallow" part. Not all UK "masters" degrees match up very well with US degree programs. This is particularly true for geotechnical engineering for some reason. Your experience...
Using what design approach? What foundation type? Kind of structure?
[pacman]
Please see FAQ731-376 for great suggestions on how to make the best use of Eng-Tips Fora. See faq158-922 for recommendations regarding the question, "How Do You Evaluate Fill Settlement Beneath Structures?"
DSS is a nice test, but it is seldom used in practice. If the client wants you to run DSS tests, establish a firm contract for that firm to purchase x number of DSS tests per quarter until the machine is paid for.
This will quickly determine the seriousness of their intent...
[pacman]
Please...
You still need to evaluate the surcharge independently, then add the pressure distribution to the back of the wall. Don't try to use an equivalent fluid approach for surcharges - it's not appropriate for most problems.
[pacman]
Please see FAQ731-376 for great suggestions on how to make the...
