Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by crackman

  1. crackman

    Aircraft - Fatigue Load Spectrum

    For in-depth explanation of developing fatigue external and internals and spectra, there are several presentations in the past years you can obtain from past AFGROW and ASIP conference proceedings websites and there is also a full week long course offered. With regards to GAG cycle being the...
  2. crackman

    Hi, As per the document "Fatigue

    Hi Sparweb Yes, lots of folks have made the same mistake and there are some issues with the simplified method too. Along with a friend of mine we teach a 40 hour class twice a year which goes thru the full flight by flight spectrum development process as well as the simple once per flight gag...
  3. crackman

    Hi, As per the document "Fatigue

    Hi Hate to disagree with anyone here but gag damage being the most significant is just not true. It actually depends on the mission profiles and utilization as well as where on the airframe. For example,actual data shows large transport aircraft like 747, 767, 777, 787, A330, A340, etc have GAG...
  4. crackman

    Hi, As per the document "Fatigue

    Hi Jnnal There are many papers on spectrum development in the public domain and in particular on the gag cycle, see the ASTMs. Just be very careful about trying to use one equivalent gag cycle to represent the same damage as a full spectrum, This usually does not work. You need to first know the...
  5. crackman

    Jetblue 292 landing

    Hi This accident was due to fatigue failure of the anti-rotation lugs. This is one I have covered many times in our DTA course. This was actually missed because the fatigue loads on this part were not representative. The fatigue spectrum did not account for a large number of added cycles which...
  6. crackman

    Looking For Boeing Design Manual Reference -Frame Analysis

    You got me, not the best at typing on this particular site using my phone. Obviously, I meant "uses", fingers are too fat ;) With regards to Bruhn, took me years to get a copy of his missile structures book, its pretty hard to find. It does have a nice reference to a method for developing...
  7. crackman

    Looking For Boeing Design Manual Reference -Frame Analysis

    Hi rb1957 Not entirely. The efforts on developing methods for ring analyses goes back even before ww2 and spans the globe. Here are some earlier papers (some easier to find than others): "A Solution of the Circular Ring", by Roy Miller, May 2, 1931; "Monocoque Fuselage Circular Ring...
  8. crackman

    Looking For Boeing Design Manual Reference -Frame Analysis

    Hi All Just to add some relevant information. All of the OEM stress manuals I have seen (Boeing, Grumman, Lockheed, McDonnell Douglas, Curtiss Wright, etc.) including both new and old versions, all reference the NACA series of methods for ring frame analysis. The method depends on the time...
  9. crackman

    Is Diagonal Tension allowed

    Hi ChasGen61 As the other replies you received, yes fuselage structure is allowed to buckle so long as it is not permanent. That being said, on commercial fuselage can tend to happen around 60% of limit. So it can occur at fatigue stresses. Also, pressurization does not entirely prevent...
  10. crackman

    Strain Measurements on an Old Aircraft

    AliBaig1991 The 2500 hours you quoted in many cases is not atypical of past failures. In fact, many GA aircraft in the past have had wing failures. Here are a few for reference all of which occurred at less than 10,000 hours: Piper J-3 Cub - 1947 - 566 flight hours Twin Pioneer - 1957 - 563...
  11. crackman

    Structural analysis report examples

    Hi eix Unfortunately the process is not easy. First of all, there are numerous archives and their search engine is not very good. Once you find the report you are interested in, you can place a request for quote which is limited to a max of 3 documents. Then it takes about 2 to 3 weeks to get a...
  12. crackman

    Structural analysis report examples

    Dear eix It is indeed a great idea to go back and look at past structural analyses. In all my years as a DER, structural reports have progressively gotten worse. Also, much analysis is performed via FEA but many engineers do not correctly validate them as they do not know how to perform the...
  13. crackman

    Structure modification no OME loads

    Dear ashco From your diagram, seems like you are modifing tha wing carry thru with an external pod? If yes, this is a big deal. I have worked the 350 on numerous projects as a DER, this is no trivial mod. As the others suggested, you need to find some expert help. In addition to external loads...
  14. crackman

    Fatigue load spectrum

    If you are trying to use a couple flight tests to extrapolate exceedance data for fatigue spectra, I can tell you, imho, that is a waste of time and will not provide any conclusive data. There are upwards of 50 or more public references (NASA, DOT/FAA, RAE, DOD, ect) with existing large...
  15. crackman

    de Havilland Comet Design changes

    found a quick snapshot from the accident report.

Part and Inventory Search